---
title: "Surrounding buildings: 3D view, noise and shading"
url: "https://knowledgebase.glintsolar.com/en/article/surrounding-buildings-3d-view-noise-and-shading"
language: "en"
last_updated: "2026-11-20T09:14:37.453Z"
---

# Surrounding buildings: 3D view, noise and shading

![](https://cdn-assets.productfruits.com/a24dffaa-518c-4dbe-8592-102fd24a635a)

  
Visualise the buildings around your site in 3D, and include them in your noise analysis.              
  
Surrounding buildings is currently only available for portfolios in France, Germany, Poland and Denmark. The building data comes from official national sources.  

### Key points 

-   Click **Buildings** in the map toolbar to show the surrounding buildings.
-   Buildings show only when you are zoomed in. If you see **Zoom in to see buildings**, zoom in until the footprints show.
-   Buildings show as footprints in 2D and as blocks with their real height in 3D.
-   In 3D, you see the buildings up to 1 km from the centre of your map view. Move the map to see buildings in a different area.
-   If **Buildings** is on when you run a noise analysis, the analysis includes the buildings up to 500 m from your equipment.
-   You can also include the buildings in your PVsyst shading scene export.

### How to show surrounding buildings

Click **Buildings** in the map toolbar. Click it again to hide the buildings.

![](https://cdn-assets.productfruits.com/131aeac6-9a0d-4158-9139-75d7a3b4c165)

Use the **2D** and **3D** buttons in the bottom right corner to change the view. In 2D, you see grey footprints. In 3D, you see grey blocks that stand on the terrain and cast shadows on your site. The 3D view shows the buildings within approximately 1 km of the centre of your map view.

### Include buildings in your noise analysis

![](https://cdn-assets.productfruits.com/3d7bb225-2197-4905-be10-fa830d9b0a1c)

Turn on **Buildings** before you run the analysis. Glint Solar then includes the buildings within 500 m of your noise emitters and equipment.

### Include buildings in your PVsyst shading scene

![](https://cdn-assets.productfruits.com/7276a084-e5db-4a34-badd-62ef930714f3)

Open the analysis report, choose **Export shading scene to PVSyst**, tick **Surrounding buildings** in the export window, and then export.

**Important Note:** The export contains only the buildings within 1 km of the centre of the map view in the analysis report. Before you export, move the map so that your site is in the centre and you can see the buildings that you want to include.

### Where the building data comes from

| Country | Publisher | Dataset | Heights |
| --- | --- | --- | --- |
| France | IGN, the French national mapping institute | BD TOPO, building class | Roof altitude minus ground altitude. If one of these is not available, we use the building height that IGN gives. |
| Germany | The surveying authorities of the 16 federal states (AdV) | Building footprints and heights from the official LoD2 3D building models of the 16 states. | Each building carries its measured height from the data. Separate building parts have their own heights. |
| Poland | GUGiK, the Polish Head Office of Geodesy and Cartography | Building footprints and floor counts from BDOT10k. Heights from the national 3D building models (CityGML LOD1, 2024 release). | Building height measured with LiDAR. For some buildings, the model has no height. For these buildings, we estimate the height from the number of above-ground floors, at 3 m for each floor. |
| Denmark | GeoDanmark and Danmarks Højdemodel | Building footprints from GeoDanmark. Heights from Danmarks Højdemodel (DHM). Floor counts from the building register (BBR). | Height is measured from the national elevation model (DHM), as roof altitude minus ground altitude, where the building was captured; buildings newer than the elevation model are estimated from the BBR floor count. |

**France:** The building height that IGN gives is to the eaves, so it is lower than the top of a pitched roof.

**Poland:** The measured height is the typical roof level, not the highest point of the roof. For some buildings, the model has no height. For these buildings, we estimate the height from the number of above-ground floors, at 3 m for each floor. We use 3 m because it is the standard floor height in Poland. This estimate does not include the roof.

### Good to know

-   Each building is a simple block with one height. Roof shapes are not shown.
-   On a slope, the base of a building is at the lowest point of the ground below it.
-   A building that is new or changed can be different from what you see on site.

### Additional resources

-   Learn how to change the view in [2D and 3D visualisation](https://knowledgebase.glintsolar.com/en/article/2d-and-3d-visualisation).
-   See how shade affects your design in [Visualize shadows on panels in 3D](https://knowledgebase.glintsolar.com/en/article/visualize-shadows-on-panels-in-3d).
-   Read about the noise model in [BESS: Noise modelling](https://knowledgebase.glintsolar.com/en/article/bess-noise-modelling).
-   Read about exports in [The analysis output report](https://knowledgebase.glintsolar.com/en/article/the-analysis-output-report).
